Hey everyone, it’s Jake from the Water Tank team — I get DMs all the time asking, “How the heck do you clean a fiberglass water tank without messing it up?” First off, full transparency: I’m not some random guy online spouting random tips. I’ve seen what happens when a tank’s neglected, or cleaned wrong, and trust me, it’s not pretty. Last year, a client of ours had a fiberglass tank that got so gunked up with algae and sediment they had to replace the whole thing early — that’s thousands of dollars they didn’t need to spend, all because they followed a random YouTube hack that used bleach straight. So today, I’m walking you through exactly how to do this the right way, no guesswork, no fancy tools, just stuff you probably already have lying around. Water Tank

First, let’s cut to the chase: fiberglass tanks are tough, but they’re not indestructible. The biggest mistake most people make is using harsh, abrasive chemicals or power washing too hard — that scratches the fiberglass, creates tiny crevices where gunk hides, and even breaks down the resin over time. Our team at the supply company has been selling fiberglass tanks for years, and we teach every client these basics from day one: prevention is way easier than fixing a dirty tank, and when you do need to deep clean, stick to gentle, non-abrasive methods.
Let’s start with the prep step, because skipping this is how you end up with chemicals in your drinking water — yikes. First, turn off the water supply to the tank, drain all the water out, and let it dry out completely. I know, I know, that takes a couple days, but hear me out: cleaning a wet tank is a disaster waiting to happen. You’ll be slipping everywhere, the gunk won’t scrape off right, and any cleaning solution you use will just get diluted. Pro tip: if it’s a small tank, you can leave the hatch open for 24-48 hours; if it’s a bigger commercial tank, we usually tell clients to use a low-power fan to speed up drying. Once it’s fully dry, put on some gloves (rubber ones, not those flimsy garden gloves) and a face mask — dust and old gunk can be gross to breathe in, trust me.
Now, the fun part: actually cleaning it. For regular, light maintenance (like every 6 months if it’s residential, every 3 months if it’s commercial), all you need is a bucket of warm water, a splash of mild dish soap (the kind you use for dishes, not heavy-duty degreaser), and a soft-bristle brush — like the one you use to wash your car, not a metal scrub brush. I’ve seen people use steel wool before and it’s a nightmare: those tiny metal shavings get stuck in the fiberglass and start rusting over time. Dip the brush in the soapy water, scrub the walls, the bottom, the corners where sediment likes to hide, and any fixtures like the inlet or outlet pipes. For algae that’s a little stubborn, don’t reach for bleach — grab a scrub pad made for non-stick pans. It’s soft enough not to scratch, but tough enough to lift light algae. Once you’re done scrubbing, rinse the entire tank out with clean water a couple times to get rid of all the soap suds and loose gunk. That’s it for routine maintenance.
But what if your tank has build-up that’s been there for months — like thick algae, mineral deposits from hard water, or even small amounts of mold? That’s when you need a deep clean, and here’s where people mess up big time. First, no bleach. I repeat, no bleach on fiberglass water tanks. Bleach breaks down the resin over time, and even small residues can get into your water. Instead, use a solution of 1/4 cup of white vinegar per gallon of warm water. Vinegar is mild, cuts through mineral deposits like magic, and it’s totally safe to rinse away. For really thick algae, let the vinegar solution sit on the walls for 15-20 minutes before scrubbing — don’t leave it longer than that, though, because even vinegar can start to eat at fiberglass if it’s left on for hours. For mold spots, add a tiny bit of baking soda to the vinegar — make a paste, spread it on the mold, let it sit 10 minutes, then scrub. Baking soda is abrasive enough for tough spots but won’t scratch fiberglass. Once you’re done deep scrubbing, you have to rinse the tank really well — like, 3 or 4 times — to make sure no vinegar or baking soda is left behind. Then let it dry completely again before refilling it with water.
Wait, what about that one time someone says to use hydrogen peroxide? Yeah, that’s fine for light mold, but only 3% household hydrogen peroxide, not the industrial kind. And always dilute it with equal parts water. I’d skip it for routine cleans, though — vinegar works just as well and is cheaper. Another hack I learned from a commercial client last year: if your tank has a lot of sediment at the bottom, after draining it, you can use a wet-dry vac to suck up the sediment before you even start scrubbing. That cuts your cleaning time in half. No more scrubbing through a pile of dirt at the bottom.
Now, let’s talk about mistakes to avoid, because I’ve seen every single one. First, power washing. I don’t care what anyone says, the high pressure from a power washer can puncture thin fiberglass, or at the very least scratch it so bad that algae grows back faster. Save the power washer for your driveway, not your tank. Second, using harsh chemicals like ammonia, chlorine, or any heavy-duty degreaser. These eat away at the fiberglass resin, shorten the life of your tank, and leaving residues in your water is a health hazard. Third, not drying the tank fully after cleaning. If you refill a damp tank, you’ll just get mold and algae growing again within a couple weeks. Fourth, cleaning too often or not often enough. Residential tanks every 6 months, commercial every 3 — that’s the sweet spot. Too often and you’ll wear down the fiberglass, too rarely and build-up gets out of hand.
Speaking of maintaining your tank so you don’t have to deep clean every time, here are a few simple habits. First, keep the lid or hatch closed at all times. That keeps debris, bugs, and sunlight out — sunlight is what makes algae grow. Second, install a filter on the inlet pipe. That catches sediment before it gets into the tank, so you don’t have all that gunk at the bottom. Third, do a quick visual check every month. Just open the hatch and peek inside — if you see early signs of algae, tackle it right away with a soapy water scrub, no need for vinegar. Catching it early saves you a ton of work later.
Now, as someone who supplies fiberglass water tanks, I get asked all the time if cleaning is hard enough that people should just buy a different material. Let me set the record straight: fiberglass is the best material for water tanks for so many reasons — it’s lightweight, durable, doesn’t rust, doesn’t leach chemicals, and holds water better than metal or plastic. The only downside is it needs gentle cleaning, but that’s true of any good tank. A steel tank needs to be painted every few years to prevent rust, a plastic tank can get scratched easily and leach chemicals over time — fiberglass just needs a little care, which is way easier than replacing the whole thing when another material fails.
If you’re new to owning a fiberglass water tank, or you’re cleaning a commercial tank for the first time, and you’re worried about doing it right, our team here has got your back. We’ve helped hundreds of clients walk through their first clean, whether it’s answering questions about what supplies to use or talking through the steps for bigger tanks. If you’re in the market for a new tank too, or you just need more tips on maintaining the one you have, don’t hesitate to reach out to us to chat more. We’re not just a supply company — we’re here to make sure your tank works for you for years to come.
Wait, one last quick tip that I forgot: after you’re done cleaning and refilling the tank, run a test of the water to make sure there are no weird tastes or smells. Even if you rinsed well, sometimes a tiny bit of vinegar can linger, and a quick test will put your mind at ease. If you do notice a smell, just drain a little more water out and refill again — that’s way easier than dealing with contaminated water.
At the end of the day, cleaning a fiberglass water tank isn’t rocket science. It’s all about being gentle, using the right supplies, and staying on top of regular maintenance. I’ve seen tanks last 20+ years with proper care, and I’ve seen them fail in 5 because of bad cleaning habits. Don’t let your tank be the latter. Take the time to do it right, and it’ll take care of your water for years.

If you have more questions, or you’re looking to upgrade to a high-quality fiberglass water tank for your home or business, feel free to get in touch to discuss your needs. We’re always here to help, no matter how big or small the project is.
Domestic Hot Water Heat Pump References:
- National Sanitation Foundation. (2020). Cleaning and Maintenance of Fiberglass-Reinforced Plastic Water Storage Tanks. NSF International.
- American Water Works Association. (2019). Operation and Maintenance of Water Storage Tanks. AWWA Manual M27.
- Fiberglass Tank & Pipe Institute. (2021). Recommended Practices for Maintenance of Fiberglass Reinforced Polymer Tanks for Potable Water Storage. FTPI Technical Bulletin 102.
- U.S. Environmental Protection Agency. (2018). Guide to Household Water Storage Tank Maintenance. EPA Office of Water.
Guangdong Luckingstar New Energy Co., Ltd.
Guangdong Luckingstar New Energy Co., Ltd. is well-known as one of the leading water tank manufacturers and suppliers in China. Please feel free to wholesale high quality water tank from our factory. For customized service, contact us now.
Address: No.255 Hexiang East RD, C Area Heshan Industrial Zone,Heshan City, Guangdong, P.R. China
E-mail: info@luckingstar.com
WebSite: https://www.luckingstar.com/